T-Bolt Series for Aluminum Extrusion – Hammer Head Screws
T-Bolt Series for Aluminum Extrusion – Hammer Head Screws
A T-bolt for aluminum extrusion turns an open T-slot into a reusable fixing point. The MINDE T-bolt series does it with a hammer-shaped head that drops through the slot opening, rotates behind the lips and clamps the part you are assembling from the outside. One head geometry, one thread standard, built for frames that get modified rather than built once and sealed.
The programme covers 8 mm and 10 mm slots, in M8 thread and lengths from 16 mm to 60 mm depending on the variant, with other slot widths, thread sizes and materials made to drawing. Across the range the constants do not change: carbon steel bodies with zinc plating as the standard finish, an SS304 option where plating would not survive, a head dimensioned to clear the slot opening while bearing on the inner lips, and a thread cut to the length that keeps two to three full turns exposed past the nut.
We build these for automation integrators, machine-guard fabricators, laboratory and cleanroom framing, solar mounting assemblers and maintenance teams who add equipment to an existing frame. What they have in common is a slot that must stay usable: fittings go on and come off, positions change, and nobody wants to dismantle a frame to add a bracket.
Buying the series means buying one interface. A slot 8 screw, a slot 8 nut and a slot 8 cover from us are dimensioned to work in the same groove, so an assembly does not fail because three suppliers each interpreted the lip depth slightly differently. Documented material and finish declarations travel with the shipment, and we mark parts to your numbering when they have to match an existing bill of materials.
How to install a hammer head screws?
1. Align the flat hammer head parallel to the opening of the Slot 8 / 10 channel, drop the bolt directly into the slot at your target position (no need to push from profile end).
2. Rotate the bolt body by 90°, the hammer head will cross the slot and lock inside the T-channel.
3. Slide the bolt freely along the slot to fine-tune to your final mounting position.
4. Put on your matching flange nut / regular hex nut, attach the bracket or panel, then tighten the nut. The bolt will stay locked and will not rotate during tightening.
5. Check tightness after assembly; adjust position by loosening the nut, rotate the bolt 90° back parallel, then take out or reposition.
Tips:
Recommended matching accessory: M8 flange nut (best for aluminum profile assembly).
Do not over-torque to avoid thread damage or profile deformation.
For heavy-load scenarios, calculate load and select proper bolt length.

T-Bolt Series for Aluminum Extrusion
FAQ
What is a hammer head screws used for?
It puts a reusable thread into an open T-slot. You drop the head in at the working position, rotate it behind the slot lips and clamp a bracket, panel or guard from the outside.
Hammer head screw, T-nut or slide-in T-bolt, which should I use?
Choose the hammer head when fittings are added after the frame is built or have to move. Choose a T-nut when you need maximum clamp area or a serrated grip. Choose a slide-in bolt when the frame is assembled in a fixed sequence and the slot must stay low-profile.
How do I identify which slot size I have?
Measure the slot opening with a caliper: 8 mm profiles use slot 8 fittings, 10 mm profiles use slot 10. Do not rely on the profile series name, because two manufacturers can label the same 40 mm profile differently.
Do you offer a stainless version?
Yes, in SS304, plain finish. It shares the drawing family with the plated parts. Order it where washdown, condensate or outdoor exposure would attack zinc plating, and note that stainless threads need anti-seize.
Are these fasteners reusable?
Yes. The head is not deformed during installation, so a screw can be removed and refitted elsewhere in the same slot family. Replace any screw whose thread has been damaged by over-torque or cross-threading.
Which finish suits an outdoor frame?
Zinc plating is an indoor and general-workshop finish. For outdoor, washdown or coastal atmospheres send us the conditions and we quote a different base material or coating rather than extending the standard part beyond its application.
Drop-in T Head Screw Slot 10 M8
Slot 10 Drop-in Hammer Head T Bolts
M8 T Slot Bolt for Aluminium Profile


